Review of Alberg 22
Basic specs..
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The Alberg 22 is equipped with a long keel. A full keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.
The boat can enter even shallow marinas as the draft is just about 0.94 - 1.04 meter (3.08 - 3.38 ft) dependent on the load. See immersion rate below.
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Alberg 22 is 1.90, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 5.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Alberg 22 is about 69 kg/cm, alternatively 389 lbs/inch. Meaning: if you load 69 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 389 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
What is L/B (Length Beam Ratio)?
What is a Ballast Ratio?
What is Displacement Length Ratio?
SA/D (Sail Area Displacement ratio) Indicates how fast the boat is in light wind: - Cruising Boats have ratios 10-15 - Cruiser-Racers have ratios 16-20 - Racers have ratios above 20 - High-Performance Racers have ratios above 24 Sail-area/displacement ratio (SA/D ratio): 17.68
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 7m 2 (75 ft 2 ). Based on this, your favourite maritime shop can tell you the quantity you need.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
Usage | Length | Diameter | ||
Jib sheet | 6.7 m | (22.0 feet) | 10 mm | (3/8 inch) |
Genoa sheet | 6.7 m | (22.0 feet) | 10 mm | (3/8 inch) |
Mainsheet | 16.8 m | (55.0 feet) | 10 mm | (3/8 inch) |
Spinnaker sheet | 14.8 m | (48.4 feet) | 10 mm | (3/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Alberg 22 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us . Criticism helps us to improve.
22-foot Sailboat Comparisons
Catalina 22.
Chrysler 22
Login with your email address to see your favourites.
Logout of antique boat america.
Let us show you around
Show me around Go
Maybe later not now
I know how things work got it, thanks
Modal title
Modal sub-title, save to favourites, we will send you an email if anything changes for this boat., name goes here.
- Images - scroll through images here. Enter fullscreen at bottom right
- Request Details - send us a message directly to ask about this listing
- Make Offer - make an offer on this listing and we will communicate to the seller
- Email listing - send this listing to yourself or a friend by email
- Print Boat - print this listing for future reference
- Boat Summary - full details on this listing are available here
- Help - Click here to bring back this guide
22 Feet 1979 Allen Nye Yachts Alberg 22 Sailboat
$4,995 (usd), boat id: 37439, contact us directly - 800-675-4089, learn how the process works (faq).
Why take the kids camping when for less than the cost of a camping trailer you can own a 22 foot live-aboard sailboat. The Alberg 22 sleeps 4 comfortably and is equipped with a head (toilet) with extended range tank, sink and cooler for your food and beer. The Alberg 22 is a safe sail boat with a full keel it is self righting, several Alberg 22 have sailed across the Atlantic to Europe. The boat comes equipped with Roller Furling Jib and Genoa, the main sail is slab reefing. The boat is in excellent condition with one small patch in the main sail. The boat comes with anchor and line as well as a 6 hp Johnson auxiliary outboard mounted in the lazerette. The Alberg 22 was purchased new in 1979and equipped with a new 6 hp Johnson outboard motor.
People who viewed this boat also found these interesting
19 feet 1937 chris craft custom runabout.
A true barn find. Just taken out of a barn that it had been sitting in for ...
$22,500 (USD)
22 feet 1930 gar wood runabout.
Model 22-30 Runabout from first production year. This is the 14th built acc ...
$86,000 (USD)
20 feet 1956 century coronado.
Exceptionally clean 1956 Coronado. The 1956 Century Coronado was the ideal ...
$38,900 (USD)
18feet feet 1904 faye and bowen.
Acquired from Don Dannenberg, this is one of the earlier boats produced by ...
$3,500 (USD)
21 feet 1955 chris-craft cobra.
1955 21 ft. Chris Craft Cobra. This example of the 21 ft. Cobra is absolute ...
$234,900 (USD)
15 feet 1938 wagemaker wolverine.
Current owner has had the boat for 13 years. The wood in this boat is in ve ...
$5,000 (USD)
19 feet 1937 chris-craft custom runabout.
One of only 328 Chris-Craft Custom Runabouts built between 1935 and 1938. T ...
$29,500 (USD)
14 feet 1957 yellow jacket monterrey.
The boat was completely restored in 2009. The cold molded hull was in great ...
$20,000 (USD)
30 feet 1964 lyman boat works islander hardtop.
Well cared-for, big and sturdy, this Lyman is the quintessential boat for h ...
$39,900 (USD)
18 feet 1952 acme industries aqua liner.
Hull is made of laminated mahogany, birch decks, oak dash. Twin 17 gallon ...
$11,500 (USD)
The Alberg 22 is a 22.0ft masthead sloop designed by Carl Alberg and built in fiberglass by Nye Yachts (CAN) since 1970.
180 units have been built..
The Alberg 22 is a heavy sailboat which is a reasonably good performer. It is very stable / stiff and has a good righting capability if capsized. It is best suited as a coastal cruiser.
Alberg 22 for sale elsewhere on the web:
Main features
Model | Alberg 22 | ||
Length | 22 ft | ||
Beam | 7 ft | ||
Draft | 3.08 ft | ||
Country | Canada (North America) | ||
Estimated price | $ 0 | ?? |
Login or register to personnalize this screen.
You will be able to pin external links of your choice.
See how Sailboatlab works in video
Sail area / displ. | 17.39 | ||
Ballast / displ. | 48.13 % | ||
Displ. / length | 348.77 | ||
Comfort ratio | 20.79 | ||
Capsize | 1.90 |
Hull type | Monohull long keel | ||
Construction | Fiberglass | ||
Waterline length | 16 ft | ||
Maximum draft | 3.08 ft | ||
Displacement | 3200 lbs | ||
Ballast | 1540 lbs | ||
Hull speed | 5.36 knots |
We help you build your own hydraulic steering system - Lecomble & Schmitt
Rigging | Masthead Sloop | ||
Sail area (100%) | 236 sq.ft | ||
Air draft | 0 ft | ?? | |
Sail area fore | 121.41 sq.ft | ||
Sail area main | 114 sq.ft | ||
I | 27.75 ft | ||
J | 8.75 ft | ||
P | 24 ft | ||
E | 9.50 ft |
Nb engines | 1 | ||
Total power | 0 HP | ||
Fuel capacity | 0 gals |
Accommodations
Water capacity | 0 gals | ||
Headroom | 0 ft | ||
Nb of cabins | 0 | ||
Nb of berths | 0 | ||
Nb heads | 0 |
Builder data
Builder | Nye Yachts (CAN) | ||
Designer | Carl Alberg | ||
First built | 1970 | ||
Last built | 0 | ?? | |
Number built | 180 |
Modal Title
The content of your modal.
Personalize your sailboat data sheet
Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.
- Sailboat Guide
South Coast 22
South Coast 22 is a 22 ′ 0 ″ / 6.7 m monohull sailboat designed by Carl Alberg and built by South Coast Seacraft Co. starting in 1968.
Rig and Sails
Auxilary power, accomodations, calculations.
The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.
Classic hull speed formula:
Hull Speed = 1.34 x √LWL
Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio .311 Hull Speed = Max Speed/Length ratio x √LWL
Sail Area / Displacement Ratio
A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.
SA/D = SA ÷ (D ÷ 64) 2/3
- SA : Sail area in square feet, derived by adding the mainsail area to 100% of the foretriangle area (the lateral area above the deck between the mast and the forestay).
- D : Displacement in pounds.
Ballast / Displacement Ratio
A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.
Ballast / Displacement * 100
Displacement / Length Ratio
A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.
D/L = (D ÷ 2240) ÷ (0.01 x LWL)³
- D: Displacement of the boat in pounds.
- LWL: Waterline length in feet
Comfort Ratio
This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.
Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam 1.33 )
- D: Displacement of the boat in pounds
- LOA: Length overall in feet
- Beam: Width of boat at the widest point in feet
Capsize Screening Formula
This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.
CSV = Beam ÷ ³√(D / 64)
South Coast redesigned the Alberg SOUTH COAST 21 by lengthening it, enlarging the cabin trunk, and replacing the fin keel with a swing keel. It was the most successful boat built by South Coast Co. with over 3000 produced. Nearly the same as the NORTHBRIDGE ECLIPSE.
Embed this page on your own website by copying and pasting this code.
- About Sailboat Guide
©2024 Sea Time Tech, LLC
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
- New Sailboats
- Sailboats 21-30ft
- Sailboats 31-35ft
- Sailboats 36-40ft
- Sailboats Over 40ft
- Sailboats Under 21feet
- used_sailboats
- Apps and Computer Programs
- Communications
- Fishfinders
- Handheld Electronics
- Plotters MFDS Rradar
- Wind, Speed & Depth Instruments
- Anchoring Mooring
- Running Rigging
- Sails Canvas
- Standing Rigging
- Diesel Engines
- Off Grid Energy
- Cleaning Waxing
- DIY Projects
- Repair, Tools & Materials
- Spare Parts
- Tools & Gadgets
- Cabin Comfort
- Ventilation
- Footwear Apparel
- Foul Weather Gear
- Mailport & PS Advisor
- Inside Practical Sailor Blog
- Activate My Web Access
- Reset Password
- Customer Service
- Free Newsletter
Blue Jacket 40 Used Boat Review
Catalina 270 vs. The Beneteau First 265 Used Boat Match-Up
Ericson 41 Used Boat Review
Mason 33 Used Boat Review
How to Create a Bullet-Proof VHF/SSB Backup
Tips From A First “Sail” on the ICW
Tillerpilot Tips and Safety Cautions
Best Crimpers and Strippers for Fixing Marine Electrical Connectors
Polyester vs. Nylon Rode
Getting the Most Out of Older Sails
How (Not) to Tie Your Boat to a Dock
Stopping Mainsheet Twist
Fuel Lift Pump: Easy DIY Diesel Fuel System Diagnostic and Repair
Ensuring Safe Shorepower
Sinking? Check Your Stuffing Box
What Do You Do With Old Fiberglass Boats?
Boat Repairs for the Technically Illiterate
Boat Maintenance for the Technically Illiterate
Whats the Best Way to Restore Clear Plastic Windows?
Stopping Holding-tank Odors
Giving Bugs the Big Goodbye
Galley Gadgets for the Cruising Sailor
The Rain Catcher’s Guide
Sailing Gear for Kids
What’s the Best Sunscreen?
UV Clothing: Is It Worth the Hype?
Preparing Yourself for Solo Sailing
R. Tucker Thompson Tall Ship Youth Voyage
On Watch: This 60-Year-Old Hinckley Pilot 35 is Also a Working…
On Watch: America’s Cup
On Watch: All Eyes on Europe Sail Racing
Dear Readers
- Sailboat Reviews
One of the oldest fiberglass boats, this traditional overnighter is long on looks, short on space.
The Sea Sprite 23 is a trim but rugged daysailer-overnighter from naval architect Carl A. Alberg that enjoyed a 25-year production run under several different Rhode Island builders, most notably Clarke Ryder. It’s a typical Alberg design—narrow beam, full keel and conservative ballast-to-displacement ratio and graceful lines. This is a boat that still turns heads when it sails into a harbor.
The origins of the Sea Sprite 23 go back to 1958 when the small American Boat Building company of East Greenwich, Rhode Island, wanted to expand its product line, consisting at the time of the Block Island 40. Carl Alberg, then in the U.S. Coast Guard, came up with a 22 1/2-foot, full-keel design. (We’re not sure what Alberg’s duties were in the Coast Guard, but they apparently left plenty of free time; besides the Sea Sprite, Alberg also drew the Pearson Triton and Bristol 27 while in the service.) The Sprite, incidentally, was first marketed as a 22; a later builder accentuated the positive and it became the 23.
American Boat Building employee Tom Potter Remembers being asked to test sail the new design. “We were terribly impressed by the boat, the way it performed.” It was, Potter said, typical of most of the boats Alberg would design over the years—”sensible boats you could take to sea.”
When American Boat Building dissolved during the early 1960s, production of the Sea Sprite was taken over by the nearby Wickford Shipyard, which built it for several years, after which the molds passed briefly to Sailstar, another small Rhode Island company, then to Clint Pearson, who was starting up his own Bristol Boat Company across Narragansett Bay.
Earlier, cousins Clint and Everett Pearson had obtained the rights to the Triton, which American Boat Building for some reason had not wanted. But when Bristol employee Paul Coble designed the Corsair 24, the rights to the Sea Sprite were sold to another Bristol builder, Clarke E. Ryder. This was about 1974, and Ryder continued to build the 23 until 1985 when his company folded.
Ryder built new molds for the boat, encapsulating the heretofore external lead keel and creating a self-bailing cockpit. Except for a few other minor changes and the introduction of hull colors besides white—bright red, blue and green—the Sea Sprite 23 built by Ryder (he began with hull #525) was fundamentally the same as the first off the line at American Boat Building. All told, the model reached a run of nearly 800 before Ryder closed the doors on this highly successful boat.
Like most of Alberg’s boats, the 23 is relatively narrow of beam (7′ 0″) and heavily ballasted—43 percent of its weight is in the full keel. Freeboard and superstructure are low, which makes for pleasing lines but less than spacious accommodations below. In short, this is a boat designed for sailing and not lounging around belowdecks.
With a waterline length of just 16′ 3″, the boat rated well (16.6) under the old Cruising Club of America (CCA) rules. It is intended to heel 30 degrees or so when underway (some regard this as initial tenderness), adding waterline length and increasing hull speed. The heeling angle plus the low freeboard—the rail gets close to the water—can bring an occasional dousing for the crew in a chop. But the boat is inherently stable, and the gentle sheer and distinctive overhangs add to its seagoing profile. The 23 draws only three feet, virtually shoal draft and less than many smaller boats.
Under the more modern PHRF rating system, which is a performance-based handicap system rather than a measurement rule, the Sprite has an average rating of about 270 seconds per mile—hardly a rule-beater, but reasonably fast for a full-keeled 23-footer. (One owner crowed about beating those “tubby” Cape Dorys—in all likelihood a competing Alberg design.)
The Sprite carries a modest 247 square feet of sail under main and working jib. (The newer O’Day 23, by contrast, is lighter by almost 300 pounds and has 246 square feet.) Early in its career, the Sea Sprite also came in a daysailer model, with an eight-foot cockpit instead of the standard six, and with two berths below instead of four, and no galley or icebox. Apparently few were made, which is understandable because the standard model has ample cockpit space and little enough room below.
Construction
The hull, deck and cabinhouse of the Ryder-built boats are solid, hand-laid fiberglass for a tight, sound body. One owner called the boat “overbuilt.” The hull/deck joint is a typical inward flange sealed with 3M 5200 and fastened with machine screws.
Most fiberglass boats older than 10 to 15 years show deterioration of the gelcoat and require painting. This will be true of many used Sea Sprites, too. None of the owners who responded to our survey reported gelcoat blistering, however. Some of the earlier models seemed to experience slight leaks around the mast step or chainplates; several of the Ryder boats apparently had leaking from the pulpit stanchions. Otherwise, the interiors are reported to be dry. Overall, the Sea Sprites seem to be structurally sound with no major repairs called for and few, if any, cosmetic problems. A 1983 model we sailed looked almost new.
The Sea Sprite was built as a top-of-the-line “sailing yacht,” as company literature described it. The quality shows in the non-skid surfaces on the deck and deckhouse, the standard bronze hardware, including opening portlights, and in the generous use of wood—mahogany coamings and backrest and teak grabrails above, and lots of teak trim below. Ryder introduced a full interior liner (previous models were painted fiberglass), and the judicious use of holly and teak helps offset the shiny white surfaces. We don’t know whether the Sea Sprite’s teak cockpit grids were standard on all models, but they are a nice touch.
The boats, at least the Ryder version, carry a 30- foot fractionally rigged mast by Hall Spars. The mast is deck-stepped and halyards are led internally. The small deckhouse makes for a roomy foredeck, which is reached via comfortably wide walkways.
Performance
Several of our readers say the Sea Sprite exhibits fairly sluggish light-air performance, which is a common complaint among smaller full-keel boats. Others have found that raising a 130- or 150-percent genoa in winds under 10 knots makes a definite improvement.
Performance improves noticeably as the wind pipes up and the boat digs in. Although the rail is near the water, the boat, once in its sailing mode, seems very stable and the steering nicely balanced with just a hint of weather helm. The low freeboard enhances the feeling of being on the water which, for a small-boat enthusiast at least, is worth the occasional spray in a head sea. And while the keel-hung rudder doesn’t respond as rapidly as a spade would, the 23 tacks smartly enough. One owner, who now sails a J/Boat, remembered his Sea Sprite’s tacking ability as “not unreasonably slow.”
This is a small boat that handles well when the going gets rough and goes readily offshore—no worries about early reefing here. One owner we know said he “never thought twice” about sailing his Sea Sprite to Block Island or Cuttyhunk. In fact, Ryder used to tout a transatlantic trip—60 days from Wickford, Rhode Island to Falmouth, England—made in 1974 by a 21-year-old singlehander as evidence of the boat’s ocean-going qualities. (The only damage—to the skipper—occurred when he tripped on the dock in England and broke his ankle.)
Moving under power, however, is another matter. A 4-hp outboard, which is located in a well aft of the tiller, will get the boat to hull speed; anything smaller is a strain, more than 6 hp and you may experience control problems. The outboard well is the usual nuisance and several readers surveyed either had banished the motor below or would like to. The best that can be said for the well is that it preserves the lines of the boat. Outboard performance is inversely proportionate to wind and waves. Having once fought a losing battle against gusting winds, tide and current, with ground speed reduced to about zero, we can attest to the Sea Sprite’s poor performance under power in these conditions. If only the channel had been wide enough to hoist the sails….
Ryder for a time offered an optional Yanmar Model 1 GM diesel. This would no doubt eliminate many of the headaches associated with the outboard motor and well, but the weight and expense of an inboard seems difficult to justify. None of the readers responding to our questionnaire own inboard models.
Down below, the cabin is light and reasonably airy with two opening ports and a smoked hatch. Despite some complaints about the lack of room (even Clarke Ryder says the interior is best suited for stowing stuff) we found there was satisfactory sitting headroom if you are under six feet. The 6′ 0″ V-berths are too short and have minimal clearance; the 6′ 3″ settee berths in the main cabin disappear quickly under the cockpit seats. This is an interior that is definitely not for the claustrophobic, but at least you won’t need lee cloths. The marine head (many owners have replaced it with a portable head) is located in a wedge at the foot of the V-berths where its virtual inaccessibility makes the privacy issue moot. To be fair, this is typical of the arrangements on most boats of this size.
To starboard, between the forward and main berths, is the “galley,” consisting of a sink and some stowage. To port, there’s an insulated icebox and more dry storage. The sink, fed by a 10-gallon fiberglass water tank under the starboard berth, drains via a through-hull. The icebox drains into the bilge. There’s more stowage, under bunks and here and there, but it’s basically covered openings to the bilge. On deck, there’s good storage space in a port locker and a fuel locker to starboard that’s sized for a three-gallon tank.
Conclusions
The Sea Sprite 23 isn’t for everyone. A lack of space and accommodations relegates it to the daysailer/occasional overnighter category. Although it lacks cruising luxuries, it is an exceptional daysailer—seaworthy and strongly built, and with a sailing range that belies its small size. Its stability and ease of handling make it a good choice for the older sailor who doesn’t need a big boat anymore, or for a small family primarily interested in day sailing.
We saw several Sea Sprites listed for sale this past fall (1991) in the $6,500 range—a good price for a well-built boat that’s going to be around for a while. Older Sprites originally sold for $5,000 (minus sails) with the later Ryder models going for about $11,000.
The Sprites can be said to have held their value well while still representing a bargain relative to what you get. As Clarke Ryder says, “They sail like a charm and they’re pretty. People who have them love them.”
RELATED ARTICLES MORE FROM AUTHOR
Leave a reply cancel reply.
Log in to leave a comment
Latest Videos
Cabo Rico 34 Boat Review
Super Shallow Draft Sailboat: The Leeboard Sharpie
Hans Christian 41T – Boat Review
Seven dead after superyacht sinks off Sicily. Was the crew at...
Latest sailboat review.
- Privacy Policy
- Do Not Sell My Personal Information
- Online Account Activation
- Privacy Manager
- Forums New posts Unanswered threads Register Top Posts Email
- What's new New posts New Posts (legacy) Latest activity New media
- Media New media New comments
- Boat Info Downloads Weekly Quiz Topic FAQ 10000boatnames.com
- Classifieds Sell Your Boat Used Gear for Sale
- Parts General Marine Parts Hunter Beneteau Catalina MacGregor Oday
- Help Terms of Use Monday Mail Subscribe Monday Mail Unsubscribe
Alberg 22 - possible to launch / retrieve solo?
- Thread starter Anchored87
- Start date Jul 29, 2023
- Forums for All Owners
- Ask All Sailors
This seems like a heavy fixed keel boat. It’s described as trailerable but I’m wondering if that’s for storage or if it’s realistic to attempt to launch and retrieve this boat on my own with the trailer from a ramp (without a lift). I’m a fairly strong young guy for reference but seems like this one may need a lift.
The Alberg is heavy for its length, at 3200# most 22' boats weigh closer to 2000#. The issue for trailer launching a sailboat is having a vehicle that can tow the boat, with a trailer and boat equipment you'll be looking at around 5,000#. The other issue is finding a ramp that is steep enough to allow the boat to float off the trailer or have a trailer with a long enough extension. The draft is a little over 3 feet add another foot or so for the trailer height and you will need 4-5 feet of water when the wheels are submerged. Stepping the mast is the other issue. It can probably be done by one person if the set up is correct. Two people will make it much easier. While the Albert can be trailed, it is not a boat you want to keep at home and trailer to ramp for a day sail, especially single handed. It will take some time to step and unstep the mast and prep the boat for launch and retrieval. It would be easier if the boat can be kept on the trailer with the mast up, rigging the mast and putting the sails on can be time consuming. Best bet, keep it in a slip or on a mooring. You will use the boat more.
Three thousand pounds and 3' draft. You would want to check the ramps you would plan to use to make sure they're long enough and deep enough to handle the depth. Depending upon the ramp angle you'd likely need a tongue extender to get the trailer in far enough for the boat to float off. Then you'll need a monster truck to pull it up out of the water. Probably not something you'd want to do more than a couple of times a season. Lining up the boat on the trailer could also be interesting. Can you see through the water 3' down to make sure the keel is in the right place? Not around here.
Thank you @PaulK and @dlochner - I have a keep capable of 6-7k tow capacity. The expectation would be to trailer it the remainder of this season and get a mooring for next season. I just want to make sure I’d be able to take her out a few more times this year if I’m going to make the purchase now.
stickinthemud57
You have likely explored this possibility, but at my marina they have a dry storage area that makes it possible to leave the boat rigged, ready to be pulled over to the launch ramp. If your marina offers that it could make life easier.
stickinthemud57 said: You have likely explored this possibility, but at my marina they have a dry storage area that makes it possible to leave the boat rigged, ready to be pulled over to the launch ramp. If your marina offers that it could make life easier. Click to expand
Anchored87 said: Yes but free driveway storage sounded better Click to expand
stickinthemud57 said: I definitely hear that. Freedom from re-rigging and de-rigging being the advantage, of course. Click to expand
Kings Gambit
Kings Gambit said: I once owned a 3000# Grady White 20 Overnighter. I trailered it with my 1987 Bronco II which had the 6000# towing package upgrade. The Bronco II was four wheel drive, which I engaged to launch, and especially recover, the boat. If you find yourself on a wet, steep ramp with algal growth, and especially if the rear wheels are even slightly in the water, you should anticipate possible loss of rear wheel traction and maybe even slide further down the ramp trying to recover. A “monster truck” with big wheels/tires might or might not be needed to launch and recover safely, depending. But 4WD is a blessing to have for that kind of work at anytime. Engage the 4WD in lowest gear and just let the truck crawl up the ramp! The “hassle factor” for what you plan is quite high. Click to expand
I once had a keen interest in a MacGregor 26M trailerable boat. I found a guy with a 26X who was willing to take me for a sail. We met at his boat ramp, and it took an hour to set the boat up and get it in th water…we sailed and came back to the boat ramp, where we spent another hour and a half getting the boat back on the trailer, removing the sails, dropping the mast, etc. I learned 2 things that day… 1) Didn’t want a Mac 26M for Lake Michigan sailing 2) I would keep what ever boat I bought in a slip…. Greg
Tally Ho said: I once had a keen interest in a MacGregor 26M trailerable boat. I found a guy with a 26X who was willing to take me for a sail. We met at his boat ramp, and it took an hour to set the boat up and get it in th water…we sailed and came back to the boat ramp, where we spent another hour and a half getting the boat back on the trailer, removing the sails, dropping the mast, etc. I learned 2 things that day… 1) Didn’t want a Mac 26M for Lake Michigan sailing 2) I would keep what ever boat I bought in a slip…. Greg Click to expand
stickinthemud57 said: Good decisions, both, and this from a Mac 26S owner. Click to expand
Not addressing water ballast vs. fixed keel issue, but in general: trying to sail off a trailer would be reasonable (IMO) if you were launching for a week or two. To do this every time you want to sail, my god, that's one heck of a lot of work for most of us. With the Hunter 23 we had in 2001 to 2004, we ended up keeping it in a slip, and it was well worth the expense. You do save money on winter storage and haul/launch with a trailerable boat, but the cost in time/labor for regular usage if you don't have a slip or mooring is high. My recommendation would be, if you can remotely afford it, keep it in a slip during the sailing season and trailer it back to the house for the winter. Of course, you also get to take your boat by road to different locations, which most of us can't do.
SBO Weather and Forecasting Forum Jim & John
TRAILER SAILORS ADAPT. For 18 years I sailed a trailer sailer. 35 minutes to rig or take down. 1.5ft keel plus center board. I changed the mast step so that I could attach the mast and pivot it up on the mast step. It worked easily by attaching the pivot bolt then pushing the mast up from the cockpit. The stays were attached and as it reached vertical, I pulled in the jib halyard that was attached to the bow. This held the mast in place till I could step down from the boat and attach the forestay to the bow. Back the trailer into the water, float off the trailer and paddle the boat to the nearby dock. Tie up then go get the truck and park the truck and trailer. It was a slick process that allowed me to solo sail. On occasion an interested individual would ask if they could help. I gave them the jib halyard and said "When I say go pull up the mast and hold it in place while I get down and attach the wire stay". It worked easily as well. Usually if they showed interest, I would give them a sail experience for helping. Trailer sailing is a great way to enjoy the sport.
jssailem said: TRAILER SAILORS ADAPT. For 18 years I sailed a trailer sailer. 35 minutes to rig or take down. 1.5ft keel plus center board. I changed the mast step so that I could attach the mast and pivot it up on the mast step. It worked easily by attaching the pivot bolt then pushing the mast up from the cockpit. The stays were attached and as it reached vertical, I pulled in the jib halyard that was attached to the bow. This held the mast in place till I could step down from the boat and attach the forestay to the bow. Back the trailer into the water, float off the trailer and paddle the boat to the nearby dock. Tie up then go get the truck and park the truck and trailer. It was a slick process that allowed me to solo sail. On occasion an interested individual would ask if they could help. I gave them the jib halyard and said "When I say go pull up the mast and hold it in place while I get down and attach the wire stay". It worked easily as well. Usually if they showed interest, I would give them a sail experience for helping. Trailer sailing is a great way to enjoy the sport. Click to expand
Tally Ho said: Yep. Not slamming Mac’s. Just didn’t care for the water ballast boats. Greg Click to expand
Morgan donor
Go to a keel boat regatta (Star/J-22/24) and watch how fast keel boats on a trailer can be launched. All you need is a crane/hoist! I advise joining a sailing/yacht club (so equipped) to gain the use of the facility and benefit from hanging out with sailors. A public launch is usually crowded, which you'll tie up stepping your mast. Typically you won't float off without a tongue extension. Even then it really depends on the terrain. It's an exercise in masochism.
- This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register. By continuing to use this site, you are consenting to our use of cookies. Accept Learn more…
Visit our Popular Forums
- Monohull Sailboats
- Multihull Sailboats
- Powered Boats
- General Sailing
- Antares Yachts
- Fountaine Pajot
- Lagoon Catamarans
Cruising Business
- Boat Classifieds
- General Classifieds
- Crew Positions
- Commercial Posts
- Vendor Spotlight
Life Aboard a Boat
- Provisioning: Food & Drink
- Families, Kids, & Pets Afloat
- Recreation, Entertainment, & Fun
- Boat Ownership & Making a Living
- Liveaboard's Forum
Seamanship, Navigation & Boat Handling
- Seamanship & Boat Handling
- Training, Licensing, & Certification
- Health, Safety, & Related Gear
- Rules of the Road, Regulations, & Red Tape
Engineering & Systems
- Const. / Maint. / Refit
- Product / Service Reviews
- Electronics: Comms / AV
- Electrical: Batts / Gen / Solar
- Lithium Power Systems
- Engines & Propulsion
- Propellers & Drive Systems
- Plumbing / Fixtures
- Deck Hdw: Rigging / Sails
- Aux. Equipment & Dinghy
- Anchoring & Mooring
Photo Categories
- Member Galleries
- Life Onboard
- Sailing in the Wind
- Power Boats
- Cruising Destinations
- Maint. & Boat Building
- Marine Life
- Scuba Diving & Divers
- General Photos
Recent Photos
Listing Categories
- African Cats
- view more »
- Crew Wanted
- Crew Available
- Enhance Your Account
- Meet the Mods
- Meet the Advisors
- Signup for The Daily Cruiser Email
IMAGES
VIDEO
COMMENTS
It takes into consideration "reported" sail area, displacement and length at waterline. The higher the number the faster speed prediction for the boat. A cat with a number 0.6 is likely to sail 6kts in 10kts wind, a cat with a number of 0.7 is likely to sail at 7kts in 10kts wind. KSP = (Lwl*SA÷D)^0.5*0.5
7868 posts · Joined 2008. #2 · Oct 23, 2010. The Alberg 22 has numbers that a larger offshore boat would be proud to have. Good capsize ratio (1.9 vs 2.42 for the fin keel Catalina 22 for example) and is heavy enough to be more comfortable as well. Not quite as nimble as other lighter boats but steady and comfortable.
Review of Alberg 22. Basic specs. The Alberg 22 aka Douglass 22 is a small sailboat designed by the Swedish maritime architect Carl Alberg in the early seventies. A few hundred boats have been produced. The Alberg 22 is built by the Canadian yard Nye Yachts.
My sailboat is very similar to the Alberg-22. Here is my experience in 10+ years of sailing a 2nd generation boat by Alberg. 1.) 5.5 knots easily with only main sail and a small jib. 2.) Low freeboard, expect to get wet. 3.) Some will say it is a little tender, but than can also be a good thing. 4.)
The first option is very classic looking Alberg 22.. ... and will sail rings around the Alberg in any weather. It's commonly claimed by "classic" boat lovers that their floating brickyard is almost as fast, or 99% as fast, or 'keeps up with,' or is faster once the wind gets above XXX, or faster in waves, or something, compared to post-1950s ...
Alberg 22 I didn't have a look at any Alberg 22's before buying my Tanzer, but it was one of the boats I was considering. Just the fact that it was designed by Carl Alberg was enough to put it in the running :-). From the specs (48% ballast-to-displacement ratio), it would appear to be a very seaworthy boat.
Alberg 22. The Alberg 22 is a small recreational keelboat, built predominantly of fiberglass, with teak wooden handrails and toe rails, plus other trim. It has a masthead sloop rig, a raked stem, a raised transom, a keel-mounted rudder controlled by a tiller and a fixed long keel.It displaces 3,200 lb (1,451 kg) and carries 1,540 lb (699 kg) of ballast.
Here is my experience in 10+ years of sailing a 2nd generation boat by Alberg. 1.) 5.5 knots easily with only main sail and a small jib. 2.) Low freeboard, expect to get wet. 3.) Some will say it is a little tender, but than can also be a good thing. 4.) Sailboat will round-up at 27 knots, every time.
In LI Sound it was normal to see the 18' Typhoons heading out in 20+ knots of wind and having fun. The A22 was built by Allan Nye Scott, who also built the Alberg 29 and 34. The 22 actually has a CSF of 1.902 (anything below 2.0 is what a lot of people consider OK for offshore).
A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize. Formula. 48.17. <40: less stiff, less powerful.
Sailboat Reviews; Sailboats 21-30ft; Alberg 30 One of Carl Alberg's most successful boats, the Alberg 30 enjoyed a production run of a quarter-century. By. ... The original engine in the 30 was the Graymarine 22 hp, followed by the Atomic Four, the 10 hp single cylinder Bukh diesel, the more powerful Volvo Penta MD7A and finally the Volvo 2002. ...
Learn how the process works (FAQ) Boat Summary. $4,995 (USD) SOLD. Boat ID: 37439. Why take the kids camping when for less than the cost of a camping trailer you can own a 22 foot live-aboard sailboat. The Alberg 22 sleeps 4 comfortably and is equipped with a head (toilet) with extended range tank, sink and cooler for your food and beer.
The Pearson Commander, a 26-foot Alberg design, reaches across Narragansett Bay. (photo courtesy of Bob Muggleston) In the early 1960s, building boats designed by Carl Alberg, Philip Rhodes and Bill Tripp, Pearson Yachts was on a roll. The Alberg-designed Triton had been the catalyst; its debut at the 1959 New York Boat Show had been a runaway ...
The Alberg 22 is a 22.0ft masthead sloop designed by Carl Alberg and built in fiberglass by Nye Yachts (CAN) since 1970. 180 units have been built. The Alberg 22 is a heavy sailboat which is a reasonably good performer. It is very stable / stiff and has a good righting capability if capsized. It is best suited as a coastal cruiser.
South Coast 22 is a 22′ 0″ / 6.7 m monohull sailboat designed by Carl Alberg and built by South Coast Seacraft Co. starting in 1968. Great choice! Your favorites are temporarily saved for this session. ... South Coast redesigned the Alberg SOUTH COAST 21 by lengthening it, enlarging the cabin trunk, and replacing the fin keel with a swing ...
Designer: Carl Alberg Cabin: Yes Length: 22' Beam: 7' Draft: 3'1" Weight Empty: 3200 lbs. Ballast: 1540 lbs. Rig: Masthead Sloop Sails: Main: Bermuda 114 sq.ft. Jib: 121 sq.ft. Related boats: Alberg 30 Links: Alberg 22 at Ottawa Small Boat Messabout Great Lakes Alberg Association ...
0. The Sea Sprite 23 is a trim but rugged daysailer-overnighter from naval architect Carl A. Alberg that enjoyed a 25-year production run under several different Rhode Island builders, most notably Clarke Ryder. It's a typical Alberg design—narrow beam, full keel and conservative ballast-to-displacement ratio and graceful lines.
The Alberg is heavy for its length, at 3200# most 22' boats weigh closer to 2000#. ... Go to a keel boat regatta (Star/J-22/24) and watch how fast keel boats on a trailer can be launched. All you need is a crane/hoist! I advise joining a sailing/yacht club (so equipped) to gain the use of the facility and benefit from hanging out with sailors. ...
Alberg 22. Discussion Tools. 07-09-2012 13:24. sailing_jack. I have 2 Alberg 22's at the moment, one should be gone soon, and the other I got for my daughter, but she wants to move up now. I will refit this boat for sale, Any suggestions on what buyers would like to see done on these?
376 posts · Joined 2006. #9 · Nov 19, 2006 (Edited) Alberg 37s are classic sailing vessels. A little narrow, nice ends and sheer, easy motion at sea, and so forth. As has been said, you must find out if it meets your needs.
If you are a boat enthusiast looking to get more information on specs, built, make, etc. of different boats, then here is a complete review of undefined. Built by undefined and designed by undefined, the boat was first built in undefined. It has a hull type of undefined and LOA is undefined. Its sail area/displacement ratio undefined.