lafitte 44 sailboat

• BOAT OF THE YEAR
• Newsletters
• Sailboat Reviews
• Boating Safety
• Sails and Rigging
• Maintenance
• Sailing Totem
• Sailor & Galley
• Living Aboard
• Destinations
• Gear & Electronics
• Charter Resources
• Ultimate Boating Giveaway

• By Tim Bittel
• Updated: February 18, 2009

Honest 160-mile days, a comfort-able motion offshore, and liveaboard load-carrying capacity are hallmarks of the LaFitte 44, a Robert H. Perry design with a long fin keel and a skeg-hung rudder. Between 1980 and 1989, Chung Hwa Boatworks in Taiwan built 56 of these. Many have circumnavigated, and at least one has been sailed around twice.

The hull and deck are hand-laid fiberglass with a foam core. The hull is massively reinforced with foam-filled frames and longitudinals and with glassed-in bulkheads. A stainless-steel plate mounted on the hull frames carries the step for the Sparcraft mast. The external lead-ballast keel is solidly secured with stainless-steel bolts.

Our LaFitte 44, Tevai, was one of the few built without teak decks. On most of the boats that have them, the teak was fastened from below with screws. After 20 years of wear, the screw tips will become exposed, leading to cut feet and leaks. On some later boats, the teak was screwed down from above and the holes bunged, but this system, too, has proven prone to leaks.

Well-placed handholds serve the 2-foot-wide side decks, and the flush deck, which extends more than 22 feet forward of the deckhouse, provides a platform for offshore dinghy storage, sail changing, and anchor handling. On Tevai, the addition of a mast pulpit has greatly enhanced our security when working at the mast.

Twin bronze anchor rollers are mounted at the stem, and a locker in the foredeck contains the windlass, a wash-down spigot, and storage for deck gear. There are two chain lockers, one directly under the windlass and another farther aft, under the V-berth. Many boats have been refit with a hawsepipe to allow chain to run more freely to the after locker.

Two companionways, one amidships and one aft, give access to the interior, which is both elegantly fitted out in solid teak and functional at sea. Four hatches and eight opening ports admit light and air. Ventilated lockers and drawers abound, and deep storage is provided in lockers outboard of the settees and in two levels under the V-berth. The engine warms the wet locker.

The U-shaped galley to port features deep double sinks inboard, large work surfaces, and, between the top-loading freezer and separate fridge, 15 cubic feet of cold storage. A bin and numerous drawers and lockers provide volumes of dry storage.

Opposite is a spacious nav station. In the saloon, both the U-shaped settee to port and a straight settee to starboard convert to sea berths.

The forward stateroom has an en suite head and shower. In the aft stateroom, a queen Pullman berth to port and a settee to starboard convert to sea berths. The head/shower compartment serves as a walk-through to the saloon. Early LaFitte 44s were delivered with a 60-horsepower Lehman diesel, later ones with a Perkins. Tevai has been repowered with a 75-horsepower Yanmar. Depending on conditions, motoring range can exceed 800 miles. LaFitte 44s rarely come on the market. Recent listings have had prices ranging from $90,000 for a “needs work” boat to more than $250,000.

Tim Bittel and his wife, Pattie, have sailed Tevai, their LaFitte 44, from the Great Lakes to the southern Windward Islands.

LOA 44′ 4″ (13.51 m.) LWL 35′ 6″ (10.82 m.) Beam 12′ 8″ (3.86 m.) Draft 6′ 4″ (1.93 m.) Sail Area (100%) 927 sq. ft. (86.1 sq. m.) Ballast 11,310 lb. (5,129 kg.) Displacement 28,000 lb. (12,698 kg.) Ballast/D .40 D/L 279 SA/D 16.1 Water 110 gal. (417 l.) Fuel 115 gal. (436 l.) Engine 60-hp. Lehman or Perkins Designer Robert H. Perry

• More: 2001 - 2010 , 41 - 50 ft , bluewater sailing , Coastal Cruising , keelboat , monohull , Sailboat Reviews , Sailboats
• More Sailboats

Pre-Owned: 1988 Hylas 47

Catalina Introduces the 6 Series

Sailboat Preview: Elan GT6 Explorer

For Sale: 1984 Camper & Nicholsons 58

Galápagos: A Paradise Worth the Paperwork

Around Alone

Grease the Wheels of Your Boat: A Guide to Proper Lubrication

A Bowsprit Reborn: A DIY Renovation Story

• Digital Edition
• Customer Service
• Privacy Policy
• Terms of Use
• Email Newsletters
• Cruising World
• Sailing World
• Salt Water Sportsman
• Sport Fishing
• Wakeboarding

Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.

• Sailboat Guide

Lafitte 44 is a 44 ′ 3 ″ / 13.5 m monohull sailboat designed by Robert Perry and built by Chung Hwa Boat between 1978 and 1989.

• 12 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 13 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 14 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 15 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 16 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 17 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 18 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 19 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 20 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 21 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 22 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 23 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 24 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 25 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 26 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 27 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 28 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 29 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 30 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 31 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 32 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 33 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 34 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 35 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 36 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 37 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 38 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 39 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 40 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 41 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View
• 42 / 42 La Conner, WA, US 1981 Lafitte 44 $50,000 USD View

Rig and Sails

Auxilary power, accomodations, calculations.

The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.

Classic hull speed formula:

Hull Speed = 1.34 x √LWL

Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio .311 Hull Speed = Max Speed/Length ratio x √LWL

Sail Area / Displacement Ratio

A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.

SA/D = SA ÷ (D ÷ 64) 2/3

• SA : Sail area in square feet, derived by adding the mainsail area to 100% of the foretriangle area (the lateral area above the deck between the mast and the forestay).
• D : Displacement in pounds.

Ballast / Displacement Ratio

A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.

Ballast / Displacement * 100

Displacement / Length Ratio

A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.

D/L = (D ÷ 2240) ÷ (0.01 x LWL)³

• D: Displacement of the boat in pounds.
• LWL: Waterline length in feet

Comfort Ratio

This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.

Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam 1.33 )

• D: Displacement of the boat in pounds
• LOA: Length overall in feet
• Beam: Width of boat at the widest point in feet

Capsize Screening Formula

This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.

CSV = Beam ÷ ³√(D / 64)

From BlueWaterBoats.org :

Penned by Bob Perry , best known for associating the term “performance” with cruisers, the Lafitte 44 deviates from Perry’s performance formula to focus on comfort and style. She’s a heavy displacement double-ended cruising yacht specifically “overbuilt” to travel the world in comfort and safety.

During the mid 1970s, the boom years for cruising boats, many American designs were being outsourced to boatyards in Taiwan. It made sense to utilize the good exchange rate and the Taiwanese craftsmanship was both inexpensive and competent. Designer Bob Perry, arguably the most important designer of the modern cruising boat era was on the forefront of this trend; some say nearly every boat to come out of Taiwan had Perry’s name attached in some way. The Lafitte 44 was one of the larger boats to result from this era.

The initial concept came from Mike Lewis of the California-based Pacific Far East Industries. He commissioned Perry to design the boat and chose Taiwanese boatbuilder Chung Hwa Boatworks to build it. To oversee production, George Olivet was appointed and much of the boat’s consistency of quality can be attributed to him. Olivet went off to oversee the entire production run, enduring two ownership changes of the parent company as well as a mysterious 6 months in Taiwanese prison where he managed to continue work on the project. With Olivet, the Lafitte became one of the first Taiwanese-built yachts to enjoy continuous US onsite supervision to ensure quality. It is said that Olivet’s supervisory skills and management talent was used as an example to help move Taiwan boatbuilding from the “Dragonboat” era.

Perry penned the boat in late-1976, during this time he was in the middle of a string of of 44 footers including the Norseman 447, the Nordic 44, and the Cheoy Lee 44. He comments, “I got to know what you could do in 44 feet quite well”. Interestingly, the Lafitte just happened to be Perry’s design number 100 and urban myth has it that the night after Perry finished the design, the owners of PFEI went out to celebrate and named the boat after the Chateau Lafite wine they were drinking, but they drank too much and misspelt the the name. Lewis informs us that Lafitte is the name of the godson of one of the PFEI investors.

The first boat was introduced in 1978. Initially the boats were built without fittings installed, to be completed in California because Taiwan did not yet have enterprise zones to allow duty-free foreign hardware. Later boats were completed in Taiwan when this situation was remedied. In 1981 ownership of the concern passed from Lewis to Tom Flemming who changed the name to “Lafitte Yachts” (owners can check their hull serial numbers; starting at hull #30 the serial prefixes switched from PFE to LFT).

Ownership changed again in 1983 to Bernie Wahl who owned a dry cleaning business in upstate New York. Wahl’s vision was to turn the boat into a “Taiwanese Swan”. With close attention to detail he made many small changes that improved the boat, such as a propane system to accept 20 pound gas bottles, drawers that extended full length, and better thought out lockers. Additionally hardware suppliers were changed from West Coast to East Coast companies.

The boats continued to increase in price from 1983 due to these improvements and rising costs in Taiwan, culminating with the last hull which Wahl built for himself. (His boat had fully integrated sliding screens for each hatch and a larger more robust LeFeil mast among several changes).

Production ceased in April 1987 with a total of 56 boats, of these 53 boats remain in existence; three have been lost*.

* A record of known boats in existence is maintained on this site by LaFitte 44 owners (via wiki), feel free to contribute. Credit goes to Roy Wessbecher and Roger Young, for putting together most of the records.

Boat Configuration & Layout

The Lafitte 44 follows the double-ended theme that Perry popularized with his first design, the Valiant 40 . However the lines of the Lafitte look distinctly more modern, with its high freeboard. The bow has a moderately fine entry and sits fairly high above the water. Going below the waterline, you’ll find a deep and long fin keel drawing 6’4″ and a skeg-hung rudder.

Up above, the boat is close to being a flush-deck with its short and low cabin, faired gracefully into the deck and 22ft of foredeck that is clear and unobstructed. The side decks are 2 feet wide with well placed handholds.

Entry below is served via two companionways, one amidships and one aft. The interior is extensively fitted out with teak trim, flat surfaces and walls are in teak laminated ply. The quality of workmanship is very high. Ventilated lockers and drawers abound, providing more than ample stowage space for extended voyaging. The wet locker is warmed by the engine. The galley is very large and functional, fit for the gourmet many would say. It’s one of the most prominent features inside the boat and is set up very extremely well.

The Lafitte 44 is loaded with systems and modern conveniences from its air conditioning / heat exchangers, generator, watermaker, and many other cruising goodies. There are no less than 16 seacocks and through hull fittings.

It’s noted by some that the LaFitte 44 has a pleasant ambiance that is rare to find in a boat this size. The thick hull with its foam core and ample use of heavy wood has lead to a good amount of acoustic dampening, there’s a quiet hush as you go inside and the atmosphere is pleasantly quiet.

Construction

Standard hulls were built from hand-laid fiberglass cored with Airex foam, while it was an option to have the hull constructed of solid fiberglass laminate. The hulls were built very strong and reinforced with foam-filled frames, longitudinals and also with glassed-in bulkheads. The frame under the deck-stepped mast was reinforced with a stainless-steel plate. The decks were cored with Baltek balsa.

The ballast was cast in lead and externally mounted with stainless-steel bolts. Some owners have reported nonstructural hairline cracking at this join.

The boat is setup to make passages without fuss, it’s a stiff and dry boat with a comfortable motion. Honest 160 mile days are reported.

Buyer Notes

The LaFitte 44 is a high quality cruising yacht with many luxurious comforts and associated systems. In this regard, expect higher than norm maintenance costs. Most examples on the market tend to be in very good condition.

Links, References and Further Reading

» The Lafitte Story , Bob Perry’s recollections of the story and people behind the Lafitte 44 » Cruising World Magazine, Feb 2009, Boat Review » Yachtsurvey.com Lafitte44 review by David Pascoe » David Dodds’ SV Tenacious website, Lafitte 44 documents, magazine reviews, and links.

Thanks goes to Lafitte 44 owners Roger Young (SV Ballerina) and Roy Wessbecher (SV Breta) for their help in researching the history of this boat

Embed this page on your own website by copying and pasting this code.

Discover Related Sailboats

Blue Water Boats

This collection of capable blue water boats features time-tested sailboats with rich histories.

Tayana Vancouver 42

Cheoy Lee 44

• About Sailboat Guide

©2024 Sea Time Tech, LLC

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

• David Pascoe
• All Articles (over 180)
• Mid Size Power Boats
• Buyers' Guide to Outboard Boats
• Surveying Fiberglass Power Boats (2E)
• Marine Investigations
• Domestic (USA)
• International
• Privacy Policy
• All Articles
• Order Books

• Boat Reviews
• Buying a Boat
• Cores & Structural Issues
• Marine Engines
• Maintenance & Repairs
• Hull Blisters
• Marine Surveying
• Insurance Issues
• Boat Handling & Boat Safety
• Hurricane Preparations
• Fuel Issues

Read Online

Full Chapter One

by David Pascoe

It was with little surprise that I ran across two articles in the Wall Street Journal, and several others in non-marine publications lamenting the state of the sailboat industry. If I remember correctly, it said sailboat production for all of 1997 was barely 2000 boats. Factoring in used boat sales, sailing yachts have now declined to a scant 10% of the boating industry. While there is more than one reason for this, one of the most often cited are the ult light, highly unstable and poor handing craft that are now being produced to imitate racing craft. From boats that have such violent motions that make everybody sick, to tooth pick rigs held in place with wire threads that don't stand up long, are some of the common refrains. The latest WSJ article quoted a middle-aged lady with a lot of sailing under her belt as saying that their last boat (new) just plain made her sick. Literally, that is.

So what does this have to do with the Lafitte 44?  Nothing, I just thought it might be interesting to write this review with the state of the sailboat business in mind. If the sail boat business shrinks any further, its going to disappear altogether. Those of you who ask why I don't do more sail reviews, now you know the answer.

Who is Lafitte and where are they built? I never found out, but some literature indicates that it was formerly Pacific Far East Industries, so I'd guess Taiwan. Production, or should I say import, years are listed as 1981-86, although possibly going back further. Frankly I try to avoid reviewing Taiwan boats because they raise too much dust, but this one is a worthy exception. Like most Taiwan boats, who actually built it is something of a mystery.

This is a static review, since I only got to go over her at dockside, so I have no idea how well she sails, but she reminds me a lot of a Swan 40 I used to sail back in the early 1970's. Not only the way she looks but the way she's built.  Sturdy and well. Starting with a canoe stern, a moderately fine entry and a fairly high bow, she has a deep keel drawing 6'4" and a modest 12'8" beam, its no bathtub with a flagpole. I love the canoe stern where, instead of a reverse transom, that lops two feet off of deck space, you get an extra two feet of deck space. That's one of the stupidities of allowing racing rules to design cruising boats. The reverse transom is about one the dumbest design features around.

One look and you know she's designed to go to sea without scaring the bejesus out of everyone. The bilges are quite deep, so you know its not going to surf downwind. Nor is it going to have a curve of righting moments that will look anything like more modern boats. Its going to be stiff.

I confess to being a traditionalist, so right off you know I like the way she looks. Short, low trunk cabin faired in gracefully with a half-acre of unobstructed foredeck reminding me of a few maxi racers I've crewed on. Lord knows, I hate falling over stuff, in the dark or other wise. I like unobstructed space, even if I have to sacrifice other goodies to get it. Designed for passage making, not live aboard or gunkholing, there's no place to put your bicycles here, folks. Anybody who straps a bicycle on deck of this one ought to be executed without trial anyway. If you look closely at the above photo, you'll notice there are two 44's rafted together and that the other one has a Boston Whaler mounted on deck. Must be fun tacking, or he has a very high cut genoa.

Open the hatch and drop down below and the first thing that puzzles me is that I have entered the one and only stateroom. Hmmm. Not the first time I've seen this layout. To go to sleep at night or just to take a bit of a snooze, where'd be the noisy in place in the whole boat to do that? Right, the most frequented path is between the cockpit and refrigerator, right through that stateroom. Add to that the fact that its partially under the cockpit. Stomp, thump, thump, crash. Not the way I'd do it, but maybe some folks don't need sleep. Equally curious is that you then have to proceed through a head compartment to get to the main cabin.

Salon is plenty spacious with more than adequate seating. However, the drop leaf table is very hard to get around. Like a movie theater, nobody wants to sit in the center.

Now, there is a second companionway hatch forward of the cockpit that heads down a very steep ladder into the galley/salon. But its in a most convenient location, right under the boom. I didn't understand this arrangement either. No one is going to use this owing to the inconvenience. So what you end up with is a long-timer in the head, blocking traffic to the main cabin. Hey! Come on and get the hell out of there so I can get a beer! While there is a forward head too, have no doubt about which one gets used the most.

Speaking of galley, take a look at it. Galley seems to be what this boat is all about. I mean is this a boat layed out for a gourmet or what? Aside from the extensive woodwork, the galley is THE most prominent feature. Its designed to be used. There are a lot of things I'd do differently here, but I'm going to leave this one alone because seeing such a nice galley simply made me hungry. If you are sick to death of sandwiches and mama (or you) can cook, you'll need to think about this one. Rare to find such a nice set up.

If this doesn't have you scratching your head, surely the forward cabin will wrinkle your brow. The two berths are situated at nearly shoulder height. I don't know about you, but if I had this kind of bucks, and at my age I rather quickly got tired of four people sleeping on converted seats, with a boat this size I want a nice sleeping cabin. Not one like a tree hut where you have to climb steps to get into a bed with 3' of head room, or one with the main traffic pattern going through it, but one that seals me off from the rest of the crowd. Its not until you stop and really look at it that you realize that the sleeping accommodations aren't much different than your old 30 footer.

Woodwork, yeah. Loads of it, and good stuff too. Not fine woodwork, but well beyond the run of the mill. If you are hard on a boat and not keen on keeping it up, better go look at one of those chlorox bottles with an all glass liner. Seventeen years old and there was hardly a scratch on it. But I got to tell you, the owner has to be one son-of-a-bitch to keep it up that way. Meaning he's going to keel haul any jerk going around with a screwdriver sticking out of his back pocket. Or some such. It also means that when you see a leak, you don't look the other way but repair it immediately. Nor do you sail with the hatches open. Keeping up an interior like this is not easy and has to be treated line fine furniture, which this one was. This is a boat for wood lovers, for sure.

About the hull, here we had a problem. Not a boat for purists, it is loaded with systems, A/C, generator, water maker, lots of tankage and other gizmos. So there wasn't much of the internal hull that was visible. However, one thing is clear. Each and every partition and cabinet divider is tabbed into the hull as a frame. There must be two dozen of them, making for a hull that is very well framed. Not slopped in there with chopped strand mat either, all the tabbing is multiple layers of 2 oz cloth, all nice and neat. Chain plates? Well, there's a shot of those that tell the story. Despite not being able to see much, it took me about ten minutes to figure that this is no squeeze bottle boat. There's not going to be a problem with the rigging always going loose because of a flimsy, bendy, twisty distorting hull.

Fit and finish is pretty much first class. I'll admit I tend to lose perspective a bit when I'm on one of those superyachts and am looking at some of the finest woodwork in the world. But this is pretty good for a production boat. Notice the arched salon cabinets with the latticed panels on the doors. And everything is pretty well rounded where it should be to minimize the real bad bruises. The available literature says this boat weights 28,000 lbs. but in looking at all that woodwork, I have a hard time believing that. Wood is heavy, and there's a lot of it.

Ambiance. You hang around boats long enough and you begin to detect that boats, like rooms in a house or office, have acoustic qualities. I notice it immediately on going aboard any boat. It can have a harsh, thin, tinny sound, like a boat with fiberglass liners, or it can have a hushed, very quite atmosphere inside. When you go down below in this one, the outer world disappears. It has that nice hushed quality that only a lot of wood and mass can give it. This yacht has that ambiance that is very rare to find in a sailing yacht this size. Unfortunately, the cabin sole foundation was not laid right and it squeaks everywhere you walk. See additional comments under Mistakes below.

Rigging. The mast is a rather smallish section, which caught my attention, but so did the heavy rigging with conventional double uppers and lowers with StaLoc fittings. No nonsense here at all. All first rate stuff with a good layout for your winching and sheet leads. I don't see anything to complain about here. Except in really heavy weather I'd be looking at the spar a lot.

Teak Decks.  Nice, but . . . .  However thick they were originally, they are now worn down to the screw heads. That's a problem that rarely, if ever, gets remedied because of the tremendous cost. It is at this point that nice yachts begin to go downhill in a hurry because now the appearance of the yacht is sullied more or less for the duration. The value drops and then people who can't really afford these yachts buy them. At which point the deck surely will not be replaced.

The lack of engine access can make one rather unhappy. Bilge spaces are fairly crammed with systems.

Systems. Ugh, this is not the way I'd do things. The engine is buried in a hole with very poor access. Awful, really. The generator in the lazarette is an add-on, or so I believe. The lazarette is accessed through a hatch behind the cockpit coaming. Since there are no seat lockers, stuff tends to get thrown down there. Problem is the steering gear is right there, and it piles up in opening, making it harder to reach the generator. Typical of most sail yachts, maintaining systems is about that last thing on the minds of designers. And it shows.

It was a major chore just to find where things were located. Beneath the cabin soles (see above photo) stuff is crammed into the bilge spaces with a shoe horn. Sure hope the owner can afford to pay someone else to do the maintenance because I wouldn't wish this on anybody. Cuss and bitch territory here. Bloody knuckles, too. On the other hand, the installations are as neat as they can be under the circumstances. At least there were no lame brains at work here.

Mistakes.  The major one is that the stainless steel water tanks under the salon settee are sitting on the cabin sole. The framework of the settee is what holds them in place. Can you guess what has happened? Umm hmmm. The tanks are breaking the settee apart.

I don't know if the air conditioning is after market or not, but the way it is installed looks like it was built in. If added later, it must have been at enormous cost for there are none of those shoddy hack installations like I see with so many add-ons. Problem is, too many people don't know how to install A/C, and dealing with the huge amounts of condensation the CONDENSERS produce is it. As usual, in this case the forward cabin unit is leaking condensate and, because its one of those self contained units stowed away on a shelf behind some paneling, the paneling is rotting and ruined. Installing A/C requires knowledge and care, skills that were lacking in this case.

The cockpit.  Quite small,  I wonder why one designs a boat that sleeps 8 but the cockpit will not hold 6 and will be cramped for 4. Its laid out okay, but where you going to put the rest of the people? The 40" destroyer wheel is nice, except that it doesn't fit.  Okay, so you don't mind climbing over the seats to get to the helm, but I do.  In fact, just me alone in the cockpit was tight. Most people accept the universal design principle that sailboats should be as inconvenient as possible; that navigating the decks should be an obstacle course; that one should spend the better part of his days and nights climbing over and under things. Maybe this is the real reason people have abandoned sailing in droves. Maybe they're tired of designs that seem to go out their way to make you miserable, that work you hard and wear you down. Here we've got a beautifully unobstructed foredeck, and a cockpit so cramped and tight that . . . well, no fat people or linebackers allowed. Scaled to 5'6" and under, and I'm not sure about that.

Some people write me to say, "Well, Mr. Pascoe, if you're so smart, how you have done it better?" The answer to that is just like other designers have done it better. The cockpit was sacrificed for the full, stand up aft stateroom, an unsatisfactory tradeoff since good cockpit design should be primary, the place where good design is most important, the place where you are most often. The aft stateroom and head were botched by placing it in the main traffic pattern. I would have sacrificed head room there by moving the cockpit forward with the companionway direct to the galley, where the secondary one now exists,  making the aft a secondary stateroom, while putting the master stateroom forward, eliminating the vee berth cabin and placing the forward head where the vee berth is now located. That cabin is worse than ridiculous. Then I would have created a large foc'sle for stowage rather than trying to store stuff on top of the steering gear. You'd lose a bit of salon space, but not much. And its already very large. Large settees look nice, but they mostly go unused because no one wants to sit in the middle. Center tables are a pain because they are always in the way. Get rid of it and have an L-shaped settee instead. How often are you going to want to seat 8-9 people in the salon? Six is enough, and you'll have more floor space to boot. At least the six will be able to move.

Over the decades, I've watched a lot of high quality older yachts go into decline. And I've observed how and why it happens that such fine vessels meet their end. As yachts get older, the price drops while maintenance increases dramatically. Buyers come along who can afford the price, but not the cost of keeping it up. Insufficiently knowledgeable about what it takes to keep it maintained, they learn the hard way that it costs five times or more what they expected. They own the boat for a few years, can't afford to fix what needs fixing, and so it spirals downward until it becomes one of those back lot specials.

Aside from the decks, this boat is maintained in superb condition, but the decks are the beginning of the end. Few people really understand what maintenance hogs fine yachts can be. This yacht is no exception. With all that woodwork and complex systems crammed into tight spots with poor accessibility, you can expect the annual cost of ownership to run to 15% of value easily.

My review of this yacht leaves little doubt that the designer and builder were people who knew their stuff, at least as far as construction is concerned. Anyone who writes a check this large should know what they're doing, too. If you can handle the weird layout, you'd best be prepared for some serious management tasks.

I'm ignoring the strangeness of the layout in giving this rating since inconvenience is more or less a standard feature on most sail boats.

Posted August 1, 1998

David Pascoe - Biography

David Pascoe is a second generation marine surveyor in his family who began his surveying career at age 16 as an apprentice in 1965 as the era of wooden boats was drawing to a close.

Certified by the National Association of Marine Surveyors in 1972, he has conducted over 5,000 pre purchase surveys in addition to having conducted hundreds of boating accident investigations, including fires, sinkings, hull failures and machinery failure analysis.

Over forty years of knowledge and experience are brought to bear in following books. David Pascoe is the author of:

• " Mid Size Power Boats " (2003)
• " Buyers’ Guide to Outboard Boats " (2002)
• " Surveying Fiberglass Power Boats " (2001, 2nd Edition - 2005)
• " Marine Investigations " (2004).

In addition to readers in the United States, boaters and boat industry professionals worldwide from nearly 80 countries have purchased David Pascoe's books, since introduction of his first book in 2001.

In 2012, David Pascoe has retired from marine surveying business at age 65.

On November 23rd, 2018, David Pascoe has passed away at age 71.

Biography - Long version

Boat Reviews Articles At-A-Glance

• Introduction to Boat Reviews
• Albemarle 305
• Aquasport 215
• Baha 260 Targa (not "Baja")
• Bertram Yachts
• Bertram Yachts: Introduction
• Bertram 26.6 II
• Bertram 28 II
• Bertram 30 Express
• Bertram 30 Moppie
• Bertram 31 SF
• Bertram 33 SF
• Bertram 36 Moppie
• Bertram 42 Convertible
• Bertram 46 Convertible
• Blackfin Yachts
• Blackfin 29 SF
• Blackfin 29 Combi
• Blackfin 32 Flybridge
• Blackfin 33
• Boston Whaler Outrage 26
• Cabo 31 Sport Express
• Century 3000
• Chris-Craft 302 Crown
• Contender 25
• Cranchi Mediterranee 40
• Cruisers 4270 Esprit
• Cruisers 4280
• Glacier Bay 2640 Renegade
• Grady-White Offshore 24
• Grady-White 24 Voyager
• Grady White 272 Sailfish
• Grand Banks 42
• Gulfstar 43  Trawler-style Yacht
• Hatteras Yachts
• Hatteras Yachts: Introduction
• Hatteras 36 Convertible
• Hatteras 38 Convertible
• Hatteras 38 Convertible - Updated Review
• Hatteras 39 Sport Express
• Hatteras 45 Convertible
• Hatteras 52 Convertible
• Hatteras 53 Motor Yacht & Convertible
• Hatteras 61 Motor Yacht
• Hyatt 45 CMY
• Intrepid 289
• Island Gypsy 40
• Legacy 34 Express
• Luhrs 320 Open
• Luhrs 34 - 340 F.B. Sedan
• Luhrs Tournament 350
• Luhrs Tournament 360
• Mainship 31
• Mainship 350 Trawler
• Mako 221- Updated 11/05/99
• Maxum 4600 1998
• Morgan 462 Ketch
• Offshore 48
• Post 46 Convertible
• Pursuit 2855
• Pursuit 3000 Offshore
• Pursuit 3070 CC
• Sea Ray and Balsa Core Bottoms (from "Structural Issues")
• Sea Ray 250 Sundancer
• Sea Ray Sundancer 290
• Sea Say Sundancer 290 Update
• Sea Ray 370 AC
• Sea Ray 39 Express
• Sea Ray 500
• Shamrock 26
• Thompson Santa Cruz 2700
• Tiara Yachts
• Tiara Today
• Tiara 3100 Open
• Tiara 3600 Convertible
• Tiara 3600 Open
• Topaz 28_1981
• Trojan 10-8 Meter
• Trojan 14 Meter Convertible
• Trojan 440 Express
• Viking 43 Open
• from Buying a Boat cat.
• Marlin Monroe 42 Bertram Convertible Make an Old Boat New
• A Few Favorites

• Basic Considerations
• Boat Types: Which is Right for You?
• Old Boats, New Boats and Quality
• Basic Hull Construction
• Evaluating Boat Hulls
• Performance and Sea Keeping
• Decks & Superstructure
• Stress Cracks,Finishes and Surface Defects
• Power Options
• The Engine Room
• Electrical & Plumbing Systems
• Design Details
• Steering, Controls, Systems & Equipment
• The Art of the Deal
• Boat Shopping
• The Survey & Post Survey
• Boat Builders by Company

• What is Pre-Purchase Survey?
• Business Practices and Client Relations
• Sound vs. Seaworthiness
• Hull and Its Structure
• Surveying the Hull
• Using Moisture Meters
• Stress Cracks & Surface Irregularities
• Deck & Superstructure
• Drive Train
• Gas Engines
• Fuel Systems
• Exhaust Systems
• Electrical Systems
• Plumbing Systems

Published by: D. H. Pascoe & Co., Inc. Articles, Images: Copyright © 1997 - 2018 David H. Pascoe All rights reserved. Articles, Images: Copyright © 2019-2022 Junko A. Pascoe All rights reserved. Web site design & developement: Copyright © 1997 - 2023 Junko A. Pascoe All rights reserved. Web site: Maintained by Junko A. Pascoe

• Compare Sailboats
• Sailboat Calculators
• Bluewater Sailboats
• Catamarans and Multihulls
• Sailing Liveaboard
• Sailboats Galley
• How Much it Costs
• Sailing Destinations
• Meteorology Terms
• Sailing and Nautical Terms
• Parts of a Sailboat
• Great Explorers
• People of the Seas

Bluewater Sailboat – Lafitte 44

The Bluewater Sailboat Lafitte 44 was designed by Bob Perry, who is most known for associating the term “performance” with cruisers. It deviates from Perry’s performance formula to emphasize on comfort and aesthetics. She is a double-ended heavy displacement cruising yacht that has been “overbuilt” to sail the world in comfort and safety.

For those interested in the design of sailboats, we suggest visiting the page Sailboat Designers . This page offers valuable information and insights into the designers of sailboats and is a great resource for anyone looking to learn more about this subject.

• LOA: 44′ 4″ (13.51 m.)
• LWL: 35′ 6″ (10.82 m.)
• Beam: 12′ 8″ (3.86 m.)
• Draft, Standard**: 6′ 4″ (1.93m)
• Draft, Shoal**: 5′ 6″ (1.68m)
• Sail Area: 927 sq. ft. (86.1 sq. m.)
• Displacement: 28,000 lbs. (12,700 kg.)
• Ballast: 11,200 lbs.
• Sail Area: 619 sq. ft.
• Water: 110 US gal. (417 l.)
• Fuel: 115 US gal. (436 l.)
• Engine: 60hp Lehman or Perkins
• Designer: Robert H. Perry
• Year Introduced: 1978
• Builder: Chung Hwa Boatworks, Taiwan ** Owners report their boats draw 6″ more than specs in cruising trim

During the mid-1970s, when cruising boats were in high demand, several American designs were outsourced to Taiwanese boatyards. It made sense to take advantage of the favorable exchange rate, and Taiwanese craftsmanship was both affordable and professional. Designer Bob Perry, possibly the most influential designer of the modern cruising boat era, was at the forefront of this trend; some argue Perry’s name was tied to practically every boat that came out of Taiwan in some way. The Lafitte 44 was one of the largest boats produced during this time period.

Mike Lewis of Pacific Far East Industries in California came up with the basic idea. He commissioned Perry to design the boat and Chung Hwa Boatworks in Taiwan to build it. George Olivet was appointed to oversee production, and he is responsible for most of the boat’s constancy of quality. Olivet went out to oversee the entire production run, weathering two parent business ownership changes as well as a strange 6 months in Taiwanese prison where he managed to continue working on the project. With Olivet, the Lafitte became one of the first Taiwanese-built boats to have ongoing US onsite quality control. It is stated that Olivet’s supervisory and management abilities were used as a model to help Taiwan boatbuilding move past the “Dragonboat” era.

Perry designed the boat in late 1976, in the midst of a spate of 44-footers that included the Norseman 447, the Nordic 44, and the Cheoy Lee 44. “I got to know what you could do in 44 feet fairly well,” he says. The Lafitte was Perry’s 100th design, and legend has it that the night after Perry finalized the design, the proprietors of PFEI went out to celebrate and named the boat after the Chateau Lafite wine they were drinking, but they drank too much and misspelt the name. Lewis tells us that Lafitte is the godson of one of the PFEI investors.

The first boat was released in 1978. Because Taiwan did not yet have enterprise zones that allowed duty-free foreign hardware, the boats were initially manufactured without fittings and shipped to California for completion. When the crisis was resolved, later boats were finished in Taiwan. Lewis sold the company to Tom Flemming in 1981, who changed the name of “Lafitte Yachts” (owners can check their hull serial numbers; starting with hull #30, the serial prefixes shifted from PFE to LFT).

In 1983, ownership was transferred to Bernie Wahl, who ran a dry cleaning business in upstate New York. Wahl’s plan was to transform the boat into a “Taiwanese Swan.” He made several subtle adjustments that improved the boat, such as a propane system that could accommodate 20-pound gas bottles, drawers that extended the full length, and better-thought-out lockers. Additionally, hardware suppliers were switched from the West Coast to the East Coast.

Due to these upgrades and increased costs in Taiwan, the boats’ prices continued to rise beginning in 1983, culminating with the last hull Wahl built for himself. (Among other upgrades, his yacht had completely integrated sliding screens for each hatch and a larger, more sturdy LeFeil mast.)

Production concluded in April 1987, with a total of 56 boats produced; 53 of these boats are still in existence, while three have been lost.

LaFitte 44 owners keep a registry of known boats in existence on this site (through wiki); feel free to participate. The majority of the records were put together by Roy Wessbecher and Roger Young.

Standard hulls were hand-laid fiberglass cored with Airex foam, with the option of having the hull built of solid fiberglass laminate. The hulls were built to be extremely sturdy, with foam-filled frames, longitudinals, and glassed-in bulkheads. A stainless-steel plate was used to reinforce the frame behind the deck-stepped mast. Baltek balsa was used to core the decks.

The ballast was made of lead and was fixed on the outside with stainless-steel fasteners. Nonstructural hairline cracking has been noticed by several owners at this junction.

Performance

The boat is designed to make smooth travel; it is sturdy and dry, with a nice motion. There are genuine 160-mile days reported.

Quick Notes

The LaFitte 44 is a high-quality cruising boat with numerous opulent amenities and systems. Expect higher-than-average maintenance costs in this aspect. The majority of instances on the market are in excellent condition.

Now you can also precisely calculate the expenses related to boat ownership to make smart choices based on your budget and sailing needs. Use this bluewater Sailboat Calculator to explore different options and make the best decision.

If you are interested in learning more about the specifications and details of a sailboat, we recommend visiting the page Bluewater Sailboat data . This page provides comprehensive information and is an excellent resource for anyone seeking detailed information about 1000+ sailboats.

Subscribe to our newsletter

Don’t miss new updates on your email.

© OceanWave Sail. All Rights Reserved 2022

Terms & Conditions – Privacy Policy – Cookie Policy

About Us – Privacy Policy

• New account

Forgot your password?

Lost your password? Please enter your email address. You will receive mail with link to set new password.

Back to login

Privacy Overview

JavaScript seem to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website.

Edwards Yacht Sales

• 866.365.0706

1981 Lafitte LaFitte

• Apollo Beach, FL, US

Yacht price

• Email Broker
• Call Broker

Specifications

Descriptions, basic information, dimensions & weight.

• View Option

Presented by

Joe weber 0 listing(s).

• 941.224.9661 727.449.8222
• View Profile

Manufacturer

Length Range Length Range

Year Range Year Range

Price Range Price Range

QUICK SEARCH BY:

Buyer services, featured yacht.

1985 Morgan 31 Off Shore Fishing Cuddy

1981 Hatteras 48 Motor Yacht

2002 Linssen 470 Grand Sturdy

2005 Jefferson Rivanna 50 SDMY

2005 Island Packet 485

2023 Robalo R302 Center Console

2007 Sea Ray Sundancer 40

1996 Tiara Yachts 3500 Express

2002 American Tug Pilothouse

2007 Meridian 391 Sedan

2008 Sea Ray 47 Sedan Bridge

2000 Manta Mark II

2005 Carver 53 Voyager

1985 Ocean Yachts 55 Super Sport

2019 Monachus Issa 45

• Google Plus
• Boats For Sale
• Brokerage Services
• Sold Yachts

Whether you are buying or selling your next boat or your first boat, one of Edwards Yacht Sales 45+ Professional Yacht Brokers throughout the Southeast are here to assist. Since 2003 we have acted as our clients trusted advisor throughout the entire process from shopping, to making an offer, to sea trial and survey, to closing.

Corporate Office: 510 Brookside Drive Clearwater, FL 33764

Email: [email protected]

Phone: 727.449.8222 Toll Free: 866.365.0706 Fax: 727.298.0456

Copyright © 2024 Edwards Yacht Sales Do Not Sell My Personal Information Powered by YachtCloser

We have placed cookies on your device to help make this website better.

You can use this tool to change your cookie settings. Otherwise, we’ll assume you’re OK to continue.

Some of the cookies we use are essential for the site to work.

We also use some non-essential cookies to collect information for making reports and to help us improve the site. The cookies collect information in an anonymous form.

To control third party cookies, you can also adjust your browser settings .

Robert Perry Lafitte 44

Used yachts for sale, sail monohulls 40ft > 50ft,        robert perry boats for sale, robert perry lafitte 44 boats for sale.

1989 Lafitte 44 Cutter (Sail) SOLD

Sold see you in the med .

description

contact broker

send email to seller

Useful links.

8.10 yacht tender Ultimate Inflatable Boat Package

• Forum Listing
• Marketplace
• Advanced Search
• About The Boat
• Boat Review Forum
• SailNet is a forum community dedicated to Sailing enthusiasts. Come join the discussion about sailing, modifications, classifieds, troubleshooting, repairs, reviews, maintenance, and more!

• Add to quote

I am told this is a good blue water boat, but it doesnt appear on any of the lists. Is it taiwanise? Is it just a broker trying to sell a boat?  

They look like a really cool Robert Perry design. Check out this guys website .  

intrigued The more i read, the more i like it. thanks for the link  

Some info on them here .  

core deck Im reading that they have a Balsa core deck. I remember warnings regarding these. Saildog, or anyone have input on this design feature?  

bellefonte said: Im reading that they have a Balsa core deck. Click to expand...

I spoke with Bob Perry about the Lafitte 44 a couple of years back cos there was one for sale in Australia. I confess I didn't think much of the thing compared to other BP designs such as the Norseman 447, Passport 40/41/43, or even the Baba 40 or Valiant 40 but BP was quite positive about the design and the boats in general. To my mind it is not one of BP's best sterns but I have to admit they look better in the flesh than they do on paper. To me it still looks like a canoe stern Norseman 447 but there is no denying that for the era they have a good reputation as a fast cruiser and better than average build quality for a Taiwanese boat. Usual rules apply to buying a Taiwanese boat in particular look at the tanks. Original deck fittings and rigging could be dodgey but its unlikely in a thirty year old boat that any of the original fittings are still being used. Chain plates need careful inspection and if not already replaced are probably due for it. BP would have to try really hard to design a bad boat I reckon so its ultimately going to come down to the condition of the boat rather than any inherent problems with the design itself.  

Awesome input everyone. I am looking at one this weekend I believe. It had a lightning strike, so the electrical has been gutted. Of course, the upside would be that all the electrical will be brand new...  

I know of no boat that size from the last 30 years without a core of some kind, usually balsa, in the decks. There probably are a few though. But the Lafitte had teak decks as an option - hopefully this one doesn't as they can be a disaster after 20 years or so. The hull is cored with Airex. As tdw posted, sterns are in the eye of the beholder. But it is a solid fast boat as designed. I don't think Bob Perry has ever designed a bad boat and he had total input on this one. The biggest issue with the wiring, which is a big job in any case, is access and what has to be removed to do it. With good access it is labor heavy but you will have a new boat in this respect when done.  

Here's another review: Boat Review by David Pascoe - Lafitte 44  

I own La Fete, hull #5 and it is an awesome boat. Sails very well, quite fast, good in light wind and steady in high winds. I've been refurbishing her for nearly 5 years and in great condition. My teak decks are still in excellent condition.  

You can read Bob Perry's own thoughts about the LaFitte 44 in these two links: The Lafitte Story - By Bob Perry Double Enders According to Perry  

• ?            
• 176.3K members

Top Contributors this Month

Sailing Zingaro

Making Sailing Dreams Come True

Boat shopping: Lafitte 44

Real time update | Zingaro is on the HUNT! James tours a Bob Perry designed Lafitte 44 monohull sailboat. He says: The boat is trying to speak to you, all you have to do is listen…

This isn’t only a boat tour, but also an explanation of exactly how he goes through the boat as a pre-purchase survey.

What James figured out…

This monohull is reportedly a great sailor, and it’s big enough to fit 6 comfortably. With two separate cabins, two heads, and a convertible settee, there is plenty of room for cruising in comfort. It’s the same boat, that my buddy Brandon is taking to Antarctica – you can see some of his adventures here: Sea Change.

The Lafitte really shines in the galley, and the huge workspace and double freezer/fridge is a big plus from Zingaro’s tiny little kitchen. I’ve been on much bigger boats with smaller cooking spaces.

The engine is relatively new, and looks to be well cared for. The layout is very weird: As you come down the cockpit companionway you are greeted, instead of a boat interior, with a wall of teak – making up the aft cabin. There is a double to port with a small seating/stowage area. I would have put another quarter berth here and don’t really see the point of this waste of space…

But the rest of the interior makes sense and is very well laid out. The nav table is comfortable, the settee converts to a bed, and the aforementioned galley is quite a sight. The quarter berth is very high up, so if you are limited in mobility or a big person you are going to have a problem sleeping here.

Really the only glaring problem I saw with the boat is the teak decks. They would absolutely need to be ripped out. This a a huge job, most likely entailing the re-bedding of every deck penetration and partial replacement of the deck. Also all of the cushions and headliners need to be replaced. If you were to pay someone to do this I would imagine it would get up near $20,000, but for me to do it I think more around $5k and a month of work (preferably on the hard).

As far as price, he wants $85k.

With the layout and the deck problems I’m not really sure I’m in love with this particular boat.

Stay safe and healthy! James

You like our content? Please don’t forget to like, subcribe and share! You want more? Become part of the crew via Patreon

Discover more from Sailing Zingaro

Subscribe now to keep reading and get access to the full archive.

Type your email…

Continue reading

The Lafitte 44 is a 44.33ft cutter designed by Robert Perry and built in fiberglass by Chung Hwa Boat (TAIWAN) between 1978 and 1989.

56 units have been built..

The Lafitte 44 is a moderate weight sailboat which is a reasonably good performer. It is very stable / stiff and has an excellent righting capability if capsized. It is best suited as a bluewater cruising boat. The fuel capacity is good. There is a good water supply range.

Lafitte 44 for sale elsewhere on the web:

Main features

Login or register to personnalize this screen.

You will be able to pin external links of your choice.

See how Sailboatlab works in video

We help you build your own hydraulic steering system - Lecomble & Schmitt

Accommodations

Builder data

Modal Title

The content of your modal.

Personalize your sailboat data sheet

Paste a link here:

Give it a title:

And eventually a link to an image for the thumbnail:

LaFitte Cutter The URL for this page is Cutter Added 24-Jun-2024 © 2001-2024 ./)   . . ./)   . . 102 IMAGES Lafitte 44 Lafitte 44 Lafitte 44 Lafitte 44 Lafitte 44 1981 Lafitte LaFitte 44 Boats for Sale VIDEO ⛵️Starting ALL OVER again, in a different country!! (building a new boat) 🤯 Ep.305 'On the Other Side of the Tracks' Trailer (2014): Omar Sy, Laurent Lafitte, Sabrina Ouazani Buying a used sailboat, the used sailboat market has crashed 1 Dégustation au Château Smith Haut Lafitte Sailboat "Witch of Endor" almost gets grounded COMMENTS LAFITTE 44 LAFITTE 44 is a fin keel cutter sailboat built by Lafitte Yachts and Chung Hwa Boatworks from 1978 to 1989. It has a displacement of 28,000 lb, a sail area of 967 ft², and a design by Robert Perry. Boat Review Lafitte 44 The LaFitte 44 is a sturdy and spacious cruiser designed by Robert H. Perry and built in Taiwan. Learn about its features, performance, and price range from this boat review. Lafitte 44 Lafitte 44 is a 13.5 m monohull sailboat designed by Robert Perry and built by Chung Hwa Boat between 1978 and 1989. It is a heavy displacement double-ended cruising yacht with classic lines and overbuilt construction for world travel. Lafitte 44 Ambiance. You hang around boats long enough and you begin to detect that boats, like rooms in a house or office, have acoustic qualities. I notice it immediately on going aboard any boat. It can have a harsh, thin, tinny sound, like a boat with fiberglass liners, or it can have a hushed, very quite atmosphere inside. Bluewater Sailboat The Bluewater Sailboat Lafitte 44 was designed by Bob Perry, who is most known for associating the term "performance" with cruisers. It deviates from Perry's performance formula to emphasize on comfort and aesthetics. She is a double-ended heavy displacement cruising yacht that has been "overbuilt" to sail the world in comfort and safety. Robert Perry Lafitte 44 Blue Water Cruiser Robert Perry Lafitte 44 Blue Water Cruiser. Designed by the renowned Robert Perry, Three Sheets is a prime example of one of Bob Perry's quality cruising designs. ... "We specified each and every joiner-work detail on the boat, " said Bob Perry. "Lafitte would use only the best components and no expense was spared to make the boat top quality. " Lafitte 44 boats for sale Lafitte 44 boats for sale 1 Boats Available. Currency $ - USD - US Dollar Sort Sort Order List View Gallery View Submit. Advertisement. Save This Boat. Lafitte 44 . Ventura, California. 1980. $49,500 Seller Peninsula Yacht Sales 45. Contact. 805-984-8550. ×. Advertisement. Request Information. Contact Seller X * We weren't able to post your ... 1981 Lafitte LaFitte 44 Boats for Sale A high quality and designed cruiser/live aboard with superb sailing performance. Owner cruised for ten years in South America and has returned to Apollo Beach, FL, US. See details, photos and specifications of this vessel. 1980 Lafitte 44, Ventura California 3005 Peninsula Road. Oxnard, CA, 93035-4069. United States. 805-984-8550. View Seller Inventory. Call Now Send Email. View All. Lafitte 44 for sale in Ventura California. View pictures and details of this boat or search for more Lafitte boats for sale on boats.com. *SOLD* Beautiful on the eye and a joy to be aboard, this Lafitte 44 cutter is designed to sail the world in comfort. A strong and safe build, 'Three Sheets' is the ... Great Sailboat S/V Dream Weaver is a Robert Perry designed world cruiser. The penultimate Lafitte 44 built, Dream Weaver has been completed fitted out for serious offshore... Used Robert Perry Lafitte 44 for Sale Robert Perry Lafitte 44. La Fitte 44, GRP construction, launched 1983, powered by 60hp Perkins diesel, alloy mast, S/S rigging, Masthead Cutter rigged,...Find out more ... Robert Perry Lafitte 44 Boats For Sale. Price. NZ $179,000 negotiable. Currency 1989 Lafitte 44 Cutter (Sail) Boat Configuration & Layout The Lafitte 44 follows the double-ended theme that Perry popularized with his first design, the Valiant 40. However the lines of the Lafitte look distinctly more modern, with its high freeboard. The bow has a moderately fine entry and sits fairly high above the water. Great Sailboat Come aboard S/V Dream Weaver and take a tour of the exquisitely designed and beautifully executed interior. Lafitte 44 I spoke with Bob Perry about the Lafitte 44 a couple of years back cos there was one for sale in Australia. I confess I didn't think much of the thing compared to other BP designs such as the Norseman 447, Passport 40/41/43, or even the Baba 40 or Valiant 40 but BP was quite positive about the design and the boats in general. Boat shopping: Lafitte 44 James tours a Bob Perry designed Lafitte 44 monohull sailboat. He says: The boat is trying to speak to you, all you have to do is listen… This isn't only a boat tour, but also an explanation of exactly how he goes through the boat as a pre-purchase survey. Lafitte 44 The Lafitte 44 is a 44.33ft cutter designed by Robert Perry and built in fiberglass by Chung Hwa Boat (TAIWAN) between 1978 and 1989. 56 units have been built. The Lafitte 44 is a moderate weight sailboat which is a reasonably good performer. It is very stable / stiff and has an excellent righting capability if capsized. Sailing bluewater cruisers Lafitte 44 for sale Sailing bluewater cruisers Lafitte 44 for sale. View the broad range of sailing bluewater cruisers Lafitte 44 for sale in your area on offer in your area, review the detailed information about each vessel, compare prices, and uncover the best sailing bluewater cruisers Lafitte 44 deals $99,500 USD GLOBAL CRUISER! Proven bluewater sailboat for ... This week we find a Bob Perry-designed Lafitte 44 sailboat for sale in Marion, Massachusetts. This Lafitte 44 is a well-proven bluewater cruising sailboat th... Used Lafitte 44 for sale View the broad range of Used Lafitte 44 for sale in your area on offer in your area, review the detailed information about each vessel, compare prices, and uncover the best Used Lafitte 44 deals 1982 Lafitte 44 for sale 1981 LaFitte Cutter sailboat for sale in Washington 1981. 44'4'. 12'. 6'4'. Washington. $50,000. Description: This is the perfect live aboard boat - with great head room, large galley and ample storage. It is also a proven ocean cruising vessel that successfully went over 25,000 nautical miles around the South Pacific and back to Ketchikan, Alaska. LaFitte 44 LaFitte 44. 938 likes · 27 talking about this. a collection of photographs and information gathered from the internet on LaFitte 44 sailboats. Site creator: Ken Lund SV Full Circle LaFitte 44 Used sailing boats Lafitte 44 for sale View the broad range of Used sailing boats Lafitte 44 for sale in your area on offer in your area, review the detailed information about each vessel, compare prices, and uncover the best Used sailing boats Lafitte 44 deals. 1982 Lafitte 44 for sale Lafitte. Metropolitan City of Florence Tuscany, Italy. 1982. Used. $75,522. catamaran gulet motorboat powerboat riverboat sailboat trimaran yacht